-
1 образец испытания на растяжение
Русско-английский морской словарь > образец испытания на растяжение
-
2 образец для испытания на растяжение
Русско-английский новый политехнический словарь > образец для испытания на растяжение
-
3 испытание на усталость при растяжении
Русско-английский новый политехнический словарь > испытание на усталость при растяжении
-
4 прочность при растяжении
Русско-английский научный словарь > прочность при растяжении
-
5 образец испытания на растяжение
Русско-английский военно-политический словарь > образец испытания на растяжение
-
6 прочность на растяжение
Авиация и космонавтика. Русско-английский словарь > прочность на растяжение
-
7 удлинение при растяжении
Русско-английский научный словарь > удлинение при растяжении
-
8 испытуемый образец
Авиация и космонавтика. Русско-английский словарь > испытуемый образец
-
9 образец для испытаний на растяжение
1) Engineering: tensile sample, tensile test bar, tensile test piece, tension test bar, tension test piece, tension test specimen2) Mathematics: a tension test specimen5) Makarov: tensile test specimenУниверсальный русско-английский словарь > образец для испытаний на растяжение
-
10 образец для испытания на растяжение
1) Engineering: tensile bar, tension specimen2) Construction: tension specimen (цемента, раствора, бетона, стали)4) Polygraphy: tension test specimen5) Oil: tensile sample6) Makarov: tensile specimenУниверсальный русско-английский словарь > образец для испытания на растяжение
-
11 деформация растяжения
1. tensile deformation2. tensile strainРусско-английский большой базовый словарь > деформация растяжения
-
12 напряжение при растяжении
1. tensile stress2. tension stressшов, работающий на растяжение — tension weld
вал, работающий на растяжение — tension shaft
Русско-английский новый политехнический словарь > напряжение при растяжении
-
13 испытание призматического образца
Русско-английский военно-политический словарь > испытание призматического образца
-
14 опытный образец
-
15 пробный образец
испытательный эталон, контрольный образец — test pattern
Русско-английский новый политехнический словарь > пробный образец
-
16 испытательный образец
образец породы, взятый при канатном бурении — bailer sample
Русско-английский словарь по информационным технологиям > испытательный образец
-
17 испытательный образец
образец породы, взятый при канатном бурении — bailer sample
Бизнес, юриспруденция. Русско-английский словарь > испытательный образец
-
18 испытание без разрушения образца
[lang name="Russian"]испытательный эталон, контрольный образец — test pattern
Русско-английский научный словарь > испытание без разрушения образца
-
19 контрольный образец
1. test specimen2. check sample[lang name="Russian"]образец породы, взятый при канатном бурении — bailer sample
нарушать образец — disturb the sample; disturb the core
соответствующий образцу — up to sample, equal to sample
См. также в других словарях:
tensile test — a standard test piece is gripped at either end by suitable apparatus in a testing machine which slowly exerts an axial pull so that the steel is stretched until it breaks. The test provides information on proof stress, yield point, tensile… … Mechanics glossary
ultimate tensile strength — the highest load applied in breaking a tensile test piece divided by the original cross sectional area of the test piece … Mechanics glossary
compressive strength test — mechanical test measuring the maximum amount of compressive load a material can bear before fracturing. The test piece, usually in the form of a cube, prism, or cylinder, is compressed between the platens of a compression testing machine by … Universalium
Vickers hardness test — A Vickers hardness tester The Vickers hardness test was developed in 1924 by Smith and Sandland at Vickers Ltd as an alternative to the Brinell method to measure the hardness of materials.[1] The Vickers test is often easier to use than other… … Wikipedia
yield point — can be defined as the point where a tensile test piece begins to extend permanently. If the load is reduced to zero, the test piece will not return to its original length … Mechanics glossary
gauge length — used in the mechanical testing of steel, it is the length marked on the parallel portion of a tensile test piece from which the elongation is measured … Mechanics glossary
proof stress — the stress that will cause a specified small, permanent extension of a tensile test piece. Commonly the stress to produce 0.2% extension is quoted in N/mm2 for steel. This value approximates to the yield stress in materials not exhibiting a… … Mechanics glossary
materials testing — Introduction measurement of the characteristics and behaviour of such substances as metals, ceramics, or plastics under various conditions. The data thus obtained can be used in specifying the suitability of materials for various… … Universalium
metallurgy — metallurgic, metallurgical, adj. metallurgically, adv. metallurgist /met l err jist/ or, esp. Brit., /meuh tal euhr jist/, n. /met l err jee/ or, esp. Brit., /meuh tal euhr jee/, n. 1. the technique or science of working or heating metals so as… … Universalium
Peening — is the process of working a metal s surface to improve its material properties, usually by mechanical means such as hammer blows or by blasting with shot (shot peening). Peening is normally a cold work process (laser peening being a notable… … Wikipedia
Work hardening — Work hardening, also known as strain hardening or cold working, is the strengthening of a metal by plastic deformation. This strengthening occurs because of dislocation movements within the crystal structure of the material.[1] Any material with… … Wikipedia